Generic placeholder image

Current Nanomaterials

Editor-in-Chief

ISSN (Print): 2405-4615
ISSN (Online): 2405-4623

Research Article

Experimental Analysis of Performance and Thermal Capability of Three Phase Squirrel Cage Induction Motor Using Plastered Composite Conductors

Author(s): N. Balamurugan * and S. Selvaperumal *

Volume 4, Issue 3, 2019

Page: [201 - 205] Pages: 5

DOI: 10.2174/2405461504666190912144746

Abstract

Background: This article deals with the analysis on improved performance and efficiency of induction motor by using nano composites for stator winding.

Methods: The nanocomposites are added with different enamel. Enamel is mostly preferred for induction motors’ winding, due to three main reasons: adhesion, infusion and plaster. To predetermine the plaster and nanocomposite conductor’s behavior when they are used for transmitting AC currents and developing AC magnetic field, a numerical analysis is performed. The total heat losses are determined by the heat run test. Open circuit and short circuit tests are used to analyze the performance and efficiency of the proposed induction motor.

Results: The AC losses of composite and plaster conductors having good accord are compared with previous solid and hollow conductors. Analysis of the coil by a composite and plaster conductor shows that the AC losses in low current are lower than the coil, which is wrapped by a solid, and hallow conductors. Due to this reason, composite and plaster conductors are considered advantageous for low and medium power motors.

Conclusion: Adding nano composites with the plaster material will help to improve electrical, thermal and mechanical characteristics. The property of enamel can change the lifetime of induction motor. The induction motor winding makes use of nano composites SiO2 and TiO2 with enamel coated.

Keywords: Squirrel cage induction motor, plaster, composite, SiO2, flux and heat distribution, nanocomposites.

Graphical Abstract
[1]
Messaadi C, Ghrib T, Abdullah A, et al. Synthesis and characterization of SnO2-TiO2 nanocomposites photocatalysts. Nanosci Nanotechnol 2019; 15(04): 398-406.
[http://dx.doi.org/10.2174/1573413714666180927110912]
[2]
Milinskiy AY, Baryshnikov SV. Transitions in nanocomposites obtained by introducing KNO3 into the pores of nanosized Al2O3 films. Nanosci Nanotechnol 2019; 9(1): 128-32.
[3]
Imai T, Komiya G, Murayama K, et al. Improving epoxy-based insulating materials with nano-fillers toward practical application. In Conference Record of the. 2008 IEEE International Symposium on Electrical Insulation 2008 Jun 9 (pp. 201-204). IEEE.
[4]
Weijers HW, Trociewitz UP, Markiewicz WD, et al. High field magnets with HTS conductors. IEEE Trans Appl Supercond 2010; 20(3): 576-82.
[http://dx.doi.org/10.1109/TASC.2010.2043080]
[5]
Kumar PK, Purohit R, Hashmi SA, Kumar GR, Kumar DS. Development of nano SiO2 particles dispersed shape memory epoxy composites. App Innov Res 2019; 1: 21-4.
[6]
Chan PS, Liu C, Lin SW, et al. Application Research at the Nano and Advanced Materials Institute. IEEE Nanotechnol Mag 2011; 5(2): 13-22.
[http://dx.doi.org/10.1109/MNANO.2011.940949]
[7]
Liu. Hui, Ting Lv, Li Guangjun, et al. Preparation and characterisation of N-doped SiO2 at TiO2 core-shell structural materials and its photocatalytic property. Micro Nano Lett 2013; 8(11): 792-5.
[8]
Messaadi C, Ghrib T, Alyami AA, et al. Synthesis and characterization of SnO2-TiO2 nanocomposites photocatalysts. Curr Nanosci 2019; 15(4): 398-406.
[http://dx.doi.org/10.2174/1573413714666180927110912]
[9]
Monadi N, Saeednia S, Iranmanesh P, et al. Preparation and characterization of copper oxide nanoparticles through solid state thermal decomposition of an aqua nitrato copper(II) complex with a tridentate schiff-base ligand as a new precursor. Nanosci Nanotechnol Asia 2019; 9(1): 92-100.
[http://dx.doi.org/10.2174/2210681207666170703160109]
[10]
Thind KS, Singh J, Saini JS, Bhunia H. Mechanical and wear properties of hybrid epoxy nanocomposites. Indian J Eng Mater Sci 2015; 22(4): 421-8.
[11]
Pugazhendhi Sugumaran C, Mohan MR, Udayakumar K. Investigation of dielectric and thermal properties of nano-filler (ZrO2) mixed enamel. IEEE Trans Dielectr Electr Insul 2010; 17(6): 1682-6.
[http://dx.doi.org/10.1109/TDEI.2010.5658217]
[12]
Fraoucene H, Hatem D, Vacandio F, et al. Morphology and electronic properties of TiO2 nanotubes arrays synthesized by electrochemical method. Nanosci Nanotechnol Asia 2019; 9(1): 121-7.
[http://dx.doi.org/10.2174/2210681208666180411154247]
[13]
Kirkici H, Serkan M, Koppisetty K. Nano-dielectric materials in electrical insulation application. In 31st Annual Conference of IEEE Industrial Electronics Society, 2005. IECON 2005. 2005 Nov 6 (pp. 5-pp). IEEE.
[14]
Khan B, Goyal A. GroCE: a Gross climatic effect thermal model for three phase induction motor. Int J Eng Manage Res 2015; 5(1): 180-4.
[15]
Chang SH, Lee DG. Influence of the steel core of composite squirrel cage rotor on motor performance. Polym Compos 2001; 22(3): 371-83.
[http://dx.doi.org/10.1002/pc.10545]
[16]
Ferrando V, Orgiani P, Pogrebnyakov AV, et al. High upper critical field and irreversibility field in MgB2 coated-conductor fibers. Appl Phys Lett 2005; 87252509
[http://dx.doi.org/10.1063/1.2149289]
[17]
Baik SK, Park GS. Load test analysis of high-temperature superconducting synchronous motors. IEEE Trans Appl Supercond 2016; 26(4)5206604
[18]
Ho SL, Fu WN. Analysis of indirect temperature-rise tests of induction machines using time stepping finite element method. IEEE Trans Energ Convers 2001; 16: 55-60.
[19]
Al-Badri M, Pillay P, Angers P. A novel algorithm for estimating refurbished three-phase induction motors efficiency using only no-load tests. IEEE Trans Energ Convers 2015; 30(2): 615-25.
[http://dx.doi.org/10.1109/TEC.2014.2361258]
[20]
Çamkerten R, Erdogan S. Improvement in properties of nanocomposite materials by temperature control. Indian J Chem Technol 2012; 19: 185-90.
[21]
Kamino T, Yaguchi T, Sato T, Hashimoto T. Development of a technique for high resolution electron microscopic observation of nano-materials at elevated temperatures. J Electron Microsc 2005; 54(6): 505-8.
[http://dx.doi.org/10.1093/jmicro/dfi072] [PMID: 16495344]
[22]
Hamid M. BMetwally. Loadless full load temperature rise test for three phase induction motors. Energy Convers Manage 2001; 42(5): 519-28.
[http://dx.doi.org/10.1016/S0196-8904(00)00079-0]

© 2024 Bentham Science Publishers | Privacy Policy