Generic placeholder image

Nanoscience & Nanotechnology-Asia

Editor-in-Chief

ISSN (Print): 2210-6812
ISSN (Online): 2210-6820

General Research Article

Morphology and Electronic Properties of TiO2 Nanotubes Arrays Synthesized by Electrochemical Method

Author(s): Henia Fraoucene, Djedjiga Hatem*, Florence Vacandio and Marcel Pasquinelli

Volume 9, Issue 1, 2019

Page: [121 - 127] Pages: 7

DOI: 10.2174/2210681208666180411154247

Price: $65

Abstract

Background: A nano-tubular structure of Titanium dioxide (TiO2) was obtained using an electrochemical process based on the anodization of titanium foil in an organic electrolyte prepared with ethylene glycol (HOCH2CH2OH) containing Ammonium fluorides (NH4F) and ultrapure water under different anodization voltage. The morphological characteristics showed the formation of TiO2 nanotubes with different geometrical parameters. The electronic properties of the TiO2 NTs films were measured by the Mott-Schottky (MS) plots, indicating a positive slope for all graphs implying the n-type semiconductor nature of the TiO2 nanotubes (TiO2 NTs). The donor density (Nd) and the flat band potential (Efb) increases slightly with increase the anodization voltage.

Methods: Prior the anodization, the titanium (Ti) foils were cut into square shape (2.25 cm2) with a selected work area of 0.6 cm2. The samples were subjected to a final polishing using a rotating felt pad (01 µm) impregnated with alumina until a metallic mirror surface was obtained. The Ti foils were degreased by sonication in acetone, methanol and 2-Propanol for 10 minutes respectively, rinsed with ultrapure water and dried in a stream of compressed air. To form a TiO2 NTs, electrochemical anodization process was carried out at room temperature in Ethylene Glycol (EG) solution containing 0.3 wt% Ammonium fluorides (NH4F) and 2wt % ultrapure water for three (03) hours at different anodization voltage (20, 40 and 60V). A two-electrode cell was used for all the anodization measurements, with a platinum plate as the counter electrode, separated from the working electrode (titanium foil) by 1.5 cm. Immediately after anodization, the samples were soaked in ultrapure water to remove residual electrolyte for 10 minutes and then dried in an oven at 50 °C for 10 minutes.

Results: TiO2 NTs grown from anodization of Ti foil in fluoride EG solution for 3h by varying the anodization voltage. The micrographic analysis shows a strong influence of the anodizing voltage on the morphology and geometrical parameters of the TiO2 NTs. Non homogenous NTs morphology was observed at 20 V with the presence of corrugations along the walls of the tubes. A perfect and regular nanotublar structure with smooth’s walls tubes was obtained at an anodization voltage of 60V. Moreover, the increase of anodization voltage leads to an increase in both the diameter and the length of tubes. In fact, the inner diameter and the length of the tubes (Di and L) values increase with increasing potential, being around (39 nm and 2 µm) respectively at 20 V and (106 nm and 16,1 µm) at 60 V. The measured electronic properties of TiO2 NTs indicating the n type semiconducting nature. It is remarkable that the donor density Nd increases toward higher values by increasing the anodizing voltage until 40V. However, for an anodization at 60V, the Nd has a small decrease value (7, 03 * 1019 cm-3) indicating a diminution of defects present in the material. Also, by increasing the anodizing voltage, Efb takes increasingly more positive values. In fact, the Efb values are – 0.12, 0.05 and 0.15 V for films prepared at 20, 40 and 60 V respectively. Therefore, this behavior can be attributed to a displacement of the Fermi level toward the conduction band edge which leads to a larger band bending at the interface.

Conclusion: By varying the anodization voltage, titanium dioxide nanotubes (TiO2 NTs) were grown using electrochemical anodization of titanium foil in fluoride ethylene glycol solution for 3 hours. The morphology of the TiO2 NTs obtained was considerably affected; the anodizing potential determines the migration of ions in electrolyte during anodization process and simultaneously the tube diameter. An average small a nanotube diameter around 39 nm was obtained for 20V corresponding to 106 nm average diameter for TiO2 NTs structure synthesized at 60V. Furthermore, the semiconductor properties of the TiO2 NTs films have also been modified with increased values while increasing the anodization voltage. This behavior was attributed that the TiO2 NTs structure is more disordered, having much more defects provide abundant local donor energy levels which increases conductivity and decrease the probability of recombination of electrons and holes in these films, that can be integrated as active layer in the solar cells, in particular the Gratzel cells.

Keywords: TiO2 nanotubes, anodization process, nanomaterials, morphological characteristics, electronic properties, semiconductors.

Graphical Abstract
[1]
Hardcastle, F.D. Raman spectroscopy of titania (TiO 2) nanotubular water-splitting catalysts. J. Arkan. Acad. Sci., 2011, 65(1), 43-48.
[2]
Meyyappan, M.; Sunkara, M.K. Inorganic Nanowires: Applications, Properties and Characterization; CRC Press, Taylor and Francis: Boca Raton, FL, 2010.
[3]
Sreekantan, S.; Saharudin, K.A.; Lockman, Z.; Tzu, T.W. Fast-rate formation of TiO2 nanotube arrays in an organic bath and their applications in photocatalysis. Nanotechnology, 2010, 21(36), 365603.
[4]
Ananthakumar, S.; Ramkumar, J.; Babu, S.M. Semiconductor nanoparticles sensitized TiO 2 nanotubes for high efficiency solar cell devices. Renew. Sustain. Energy Rev., 2016, 57, 1307-1321.
[5]
Tran, V.A.; Truong, T.T.; Phan, T.A.P.; Nguyen, T.N.; Van Huynh, T.; Agresti, A.; Le, S.N. Application of nitrogen-doped TiO 2 nano-tubes in dye-sensitized solar cells. Appl. Surface . Sci., 2017, 399, 515-522.
[6]
Yan, J.; Zhou, F. TiO 2 nanotubes: Structure optimization for solar cells. J. Mater. Chem., 2011, 21(26), 9406-9418.
[7]
Maiyalagan, T.; Viswanathan, B.; Varadaraju, U.V. Fabrication and characterization of uniform TiO 2 nanotube arrays by sol--gel template method. Bull. Mater. Sci., 2006, 29(7), 705.
[8]
Varghese, O.K.; Gong, D.; Paulose, M.; Ong, K.G.; Grimes, C.A. Hydrogen sensing using titania nanotubes. Sensors . Actuat B Chem., 2003, 93(1), 338-344.
[9]
Lü, R.; Zhou, W.; Shi, K.; Yang, Y.; Wang, L.; Pan, K.; Fu, H. Alumina decorated TiO 2 nanotubes with ordered mesoporous walls as high sensitivity NO x gas sensors at room temperature. Nanoscale, 2013, 5(18), 8569-8576.
[10]
Liu, Z.; Zhang, X.; Nishimoto, S.; Murakami, T.; Fujishima, A. Efficient photocatalytic degradation of gaseous acetaldehyde by highly ordered TiO2 nanotube arrays. Environ. Sci. Technol., 2008, 42(22), 8547-8551.
[11]
Khudhair, D.; Hamedani, H.A.; Gaburro, J.; Shafei, S.; Nahavandi, S.; Garmestani, H.; Bhatti, A. Enhancement of electro-chemical properties of TiO 2 nanotubes for biological interfacing. Mater. Sci. Eng. C, 2017, 77, 111-120.
[12]
Chen, X.; Mao, S.S. Titanium dioxide nano Mater: Synthesis, properties, modifications, and applications. Chem. Rev., 2007, 107(7), 2891-2959.
[13]
Liu, N.; Chen, X.; Zhang, J.; Schwank, J.W. A review on TiO 2-based nanotubes synthesized via hydrothermal method: Formation mechanism, structure modification, and photocatalytic applications. Catal. Today, 2014, 225, 34-51.
[14]
Ou, H.H.; Lo, S.L. Review of titania nanotubes synthesized via the hydrothermal treatment: Fabrication, modification, and application. Separat. Purif. Technol., 2007, 58(1), 179-191.
[15]
Khudhair, D.; Bhatti, A.; Li, Y.; Hamedani, H.A.; Garmestani, H.; Hodgson, P.; Nahavandi, S. Anodization parameters influencing the morphology and electrical properties of TiO 2 nanotubes for living cell interfacing and investigations. Mater. Sci. Eng. C, 2016, 59, 1125-1142.
[16]
Mor, G.K.; Varghese, O.K.; Paulose, M.; Shankar, K.; Grimes, C.A. A review on highly ordered, vertically oriented TiO 2 nanotube arrays: fabrication, material properties, and solar energy applications. Solar Energy Mater. Solar. Cells, 2006, 90(14), 2011-2075.
[17]
Qin, L.; Chen, Q.; Lan, R.; Jiang, R.; Quan, X.; Xu, B.; Jia, Y. Effect of anodization parameters on morphology and photocatalysis properties of TiO 2 nanotube arrays. J. Mater. Sci. Technol., 2015, 31(10), 1059-1064.
[18]
Wang, H.; Li, H.; Wang, J.; Wu, J.; Liu, M. Influence of applied voltage on anodized TiO2 nanotube arrays and their performance on dye sensitized solar cells. J. Nanosci. Nanotechnol., 2013, 13(6), 4183-4188.
[19]
Pang, Y.L.; Lim, S.; Ong, H.C.; Chong, W.T. A critical review on the recent progress of synthesizing techniques and fabrication of TiO 2-based nanotubes photocatalysts. Appl. Catal. A General., 2014, 481, 127-142.
[20]
Assefpour-Dezfuly, M.; Vlachos, C.; Andrews, E.H. Oxide morphology and adhesive bonding on titanium surfaces. J. Mater. Sci., 1984, 19(11), 3626-3639.
[21]
Zwilling, V.; Aucouturier, M.; Darque-Ceretti, E. Anodic oxidation of titanium and TA6V alloy in chromic media. An electrochemical approach. Electrochim. Acta, 1999, 45(6), 921-929.
[22]
Gong, D.; Grimes, C.A.; Varghese, O.K.; Hu, W.; Singh, R.S.; Chen, Z.; Dickey, E.C. Titanium oxide nanotube arrays prepared by anodic oxidation. J. Mater. Res., 2001, 16(12), 3331-3334.
[23]
Cai, Q.; Paulose, M.; Varghese, O.K.; Grimes, C.A. The effect of electrolyte composition on the fabrication of self-organized titanium oxide nanotube arrays by anodic oxidation. J. Mater. Res., 2005, 20(1), 230-236.
[24]
Macák, J.M.; Tsuchiya, H.; Schmuki, P. High‐aspect‐ratio TiO2 nanotubes by anodization of titanium. Angew. Chem. Int. Ed., 2005, 44(14), 2100-2102.
[25]
Macak, J.M.; Tsuchiya, H.; Taveira, L.; Aldabergerova, S.; Schmuki, P. Smooth anodic TiO2 nanotubes. Angew. Chem. Int. Ed., 2005, 44(45), 7463-7465.
[26]
Liu, G.; Wang, K.; Hoivik, N.; Jakobsen, H. Progress on free-standing and flow-through TiO2 nanotube membranes. Solar Energy Mater. Solar. Cells, 2012, 98, 24-38.
[27]
Lei, B-X.; Liao, J-Y.; Zhang, R.; Wang, J.; Su, C-Y.; Kuang, D-B. Ordered crystalline TiO2 nanotube arrays on transparent FTO glass for efficient dye-sensitized solar cells. J. Phys. Chem. C, 2010, 114(35), 15228-15233.
[28]
Kant, K.; Losic, D. A simple approach for synthesis of TiO2 nanotubes with through-hole morphology. Phys. Status Solid RRL, 2009, 3, 139-141.
[29]
Albu, S.P.; Ghicov, A.; Berger, S.; Jha, H.; Schmuki, P. TiO2 nanotube layers: Flexible and electrically active flow-through membranes. Electrochem. Commun., 2010, 12(10), 1352-1355.
[30]
Pu, P.; Cachet, H.; Sutter, E.M.M. Electrochemical impedance spectroscopy to study photo-induced effects on self-organized TiO 2 nanotube arrays. Electrochim. Acta, 2010, 55(20), 5938-5946.
[31]
Kontos, A.G.; Kontos, A.I.; Tsoukleris, D.S.; Likodimos, V.; Kunze, J.; Schmuki, P.; Falaras, P. Photo-induced effects on self-organized TiO2 nanotube arrays: The influence of surface morphology. Nanotechnology, 2008, 20(4), 045603.
[32]
Haring, A.; Morris, A.; Hu, M. Controlling morphological parameters of anodized titania nanotubes for optimized solar energy applications. Materials., 2012, 5(10), 1890-1909.
[33]
Pasikhani, J.V.; Gilani, N.; Pirbazari, A.E. The effect of the anodization voltage on the geometrical characteristics and photocatalytic activity of TiO2 nanotube arrays. Nano-Struc. Nano-Objects, 2016, 8, 7-14.
[34]
Bauer, S.; Kleber, S.; Schmuki, P. TiO2 nanotubes: Tailoring the geometry in H3PO4/HF electrolytes. Electrochem. Commun., 2006, 8(8), 1321-1325.
[35]
Macak, J.M.; Hildebrand, H.; Marten-Jahns, U.; Schmuki, P. Mechanistic aspects and growth of large diameter self-organized TiO2 nanotubes. J. Electroanal. Chem., 2008, 621(2), 254-266.
[36]
Lu, H.F.; Li, F.; Liu, G.; Chen, Z.G.; Wang, D.W.; Fang, H.T.; Cheng, H.M. Amorphous TiO2 nanotube arrays for low-temperature oxygen sensors. Nanotechnology, 2008, 19(40), 405504.
[37]
Taveira, L.V.; Sagüés, A.A.; Macak, J.M.; Schmuki, P. Impedance behavior of TiO2 nanotubes formed by anodization in NAF electrolytes. J. Electrochem. Soc., 2008, 155(6), C293-C302.
[38]
Acevedo-Peña, P.; González, I. Relation between morphology and photoelectrochemical performance of TiO2 nanotubes arrays grown in ethylene glycol/water. Proc. Chem., 2014, 12, 34-40.
[39]
Freitas, R.G.; Santanna, M.A.; Pereira, E.C. Preparation and characterization of tio2 nanotube arrays in ionic liquid for water splitting. Electrochim. Acta, 2014, 136, 404-411.

Rights & Permissions Print Cite
© 2024 Bentham Science Publishers | Privacy Policy